- Home > Products > GPS Tracker
- VTU-609-3G×2
VTU-609-3G×2
Details
1,Attentions：
1.1, In order to help you correctly use our product, please do read this manual carefully before using.
1.2,This product can support band WCDMA 850/2100MHz,GSM 850/900/1800/1900 MHz,please choose the appropriate network operators.
1.3, Please insert SIM card before installation, ensure the SIM card has no password, otherwise the devices will not be able to work.
1.4, Please firstly make sure the devices connected correctly, and then switch on the power. Don’t install or dismount the devices if connected with power. Wrong connection may cause the device fail to work.
1.5, This product is wireless communication equipment, please cut off the power before entering the oil depots and other dangerous place.
1.6, Working voltage is from 9-36V, please do use the device under the operating voltage range, otherwise it will cause damage to the terminal or not working properly.
1.7, The device is a low power wireless transmitter and receiver ,It can receive and send radio frequency signal during the usage, in order to avoid electromagnetic interference, please stop using at any place where is forbidden.
1.8, Please use the device legally.
2, Introduction
2.1, Support 3G network: WCDMA（850/2100MHz）,GSM(900/1800 MHZ)；
2.2, GPS positioning: high sensitivity GPS module, can acquire more accuracy position
2.3,Communication function：can achieve the voice communication after connected handset phone(optional)
2.4, Monitoring Function: Remote monitoring is available Optional: External Microphone
2.5, SOS button: One key press for emergency alarm Optional: SOS button
2.6, Temperature sensor: The terminal reserved a special sensor interface, you can add a temperature sensor.
2.7, Camera: Terminal supports external camera, available to take pictures remotely
2.9, Speed detection: Terminal supports to connect to the original car speed wire to detect vehicle speed.
2.10, Analog detection:Termianl supports detection on analog signal ,such as voltage.
2.11, Antenna cut, short circuit alarm: The terminal will upload the alarm message to platform when the GPS antenna is cut and short circuit situation.
2.12, Low Battery Alarm: When battery of vehicle is too low, the terminal will upload low battery alarm to platform.
2.13, Main power cutting alarm: When the external power is cut, the alarm message will be uploaded to platform.
2.14, OTA: Terminal Supports OTA.
2.15, Remote query and setting Parameters: Via SMS and platform to query and set parameters.
2.16, Blind spots recovery：When the vehicle enter an area without network or network signal, the terminal will stock present GPS locations information and send to server once network recovers .
2.17,GeoFence,Route: Download a fence or a Route to the GPS, alarm to the platform on the line when the vehicle import area or not .
2.18,Speeding Alarm：When vehicle speed over expected limits, device will send speeding Alarm and upload to platform.
2.19, Platform Remotely Engine Cut Off: Device supports remote engine cut off.
2.20, Platform reboot: restart GPS remotely by Platform.
2.21,Multiple interfaces: 4 high or low level input interface and 3 high or low level output interface .
2.22, Overturn, collision alarm: built-in sensors can send vehicle overturn, collision alarm.
2.23,mileage statistics：device can calculate mileage since install to vehicle.
2.24,Double SIM card slot : One SIM card work when another SIM card does not work with no signal.
3,The Wiring Diagram
1、The main power lines（①）
|
Identifier
|
Colour
|
Function
|
|
|
1
|
GND
|
Black
|
The negative supply input: connected negative supply of thebattery by the car .
|
|
2
|
DC
|
Red
|
The cathode power supply input:Positive power input ：connected to the positive of the car battery，9-36V input voltage range。
|
|
3
|
SOS
|
White
|
SOS Button line,Line 3 and line 9 is connected together with the SOS switch.
|
|
4
|
ACC
|
Yellow
|
Connected to the ACC of the car , for detecting ignition state.
|
|
5
|
AD1
|
Green-White
|
A analog signal input, 0-50V input voltage range
|
|
6
|
IN1
|
Purple
|
A digital signal input 1, connect high or low input
|
|
7
|
OUT2
|
Gray-red
|
A low level output 2, connected to the relay or central lock.
|
|
8
|
OIL
|
Yellow-white
|
A low level output 1, connected to the relay or central lock.
|
|
9
|
GND
|
Black
|
SOS Button line,Line 9 and line 3 is connected together with the SOS switch.
|
|
10
|
SEN
|
Pink
|
A line connected to the digital temperature sensor
|
|
11
|
MIC+
|
White
|
Line 11 and line 12 connected to the microphone
|
|
12
|
MIC-
|
Black
|
|
2、Vice Wire（②）
|
Identifier
|
Color
|
Function
|
|
|
1
|
OUT3
|
Gray
|
A low level output 3, connected to the relay or central lock.
|
|
2
|
OUT4
|
Brown
|
A low level output 4, connected to the relay or central lock.
|
|
3
|
IN2
|
White
|
Digital Input 2,low-level input.
|
|
4
|
IN3
|
White-red
|
Digital Input 3,low-level input.
|
|
5
|
IN4
|
Blue-white
|
Digital Input 4, low-level input.
|
|
6
|
SPE
|
Blue
|
Vehicle speed input line,connected to the vehicle speed sensor
|
|
7
|
CAN-H
|
Yellow
|
CAN-H
|
|
8
|
CAN-L
|
Green
|
CAN-L
|
3、RS485（③）
|
Identifier
|
Colour
|
Function
|
|
1
|
Green
|
RS485-B
|
|
2
|
Black
|
GND
|
|
3
|
Yellow
|
RS485-A
|
|
4
|
Red
|
+5V Output
|
4、RS232（④）Interface
|
Identifier
|
Colour
|
Function
|
|
1
|
Yellow
|
TX
|
|
2
|
Green
|
RX
|
|
3
|
Red
|
+5V Output
|
|
4
|
Black
|
GND
|
5、Handset（⑤）
|
Identifier
|
Colour
|
Function
|
|
1
|
Red
|
+5V Output
|
|
2
|
Purple
|
MIC-
|
|
3
|
Green
|
RS232，RX
|
|
4
|
Yellow
|
SPK+
|
|
5
|
Blue
|
RS232，TX
|
|
6
|
Gray
|
SPK-
|
|
7
|
Brown
|
MIC+
|
|
8
|
Black
|
GND
|
6、⑤This interface is used for connecting external speakers.
4, Indicator light
|
Environment
|
LED Status
|
|
TF Card update firmware
|
When detect TF Card has update file, LED will be constant on to update firmware, will be in normal flashing when update is done.
|
|
searching the network
|
LED ON 0.5s, OFF 0.5s
|
|
already registered on the network
|
LED ON 2s, OFF 2s
|
|
Connected to server
|
LED ON 0.5s, OFF 3s
|
5、GPS Vehicle Tracker Installation
1,Check to make sure that the model is correct and complete accessories arter open the box.
2,You need a SIM card that is WCDMA (850/2100) or GSM (850/900/1800/1900) network, you can buy one from the mobile network operator.
3,The card slot is the control switch, insert the SIM card into the card slot of the terminal in the right way, terminal will start;
4,Make sure the DC line of the main power lines is connected with the power line in the vehicle, and the ACC line is connected with ACC line in the vehicle, then the The main power lines connector into the terminal, external power supply will charge the built-in battery .
5,Configure the correct parameters using SMS or PC tools, observation of the terminal LED to on line.
6,Please put the GPS antenna and the 3G antenna in a no masking signal place and connection the terminal.
7,Finally, The terminal installed in a place where is not high temperature and not high humidity.
Note: Please let installation personnel ask for PC configuration software and the setting line.
6, Hardware Parameter
|
GSM Band
|
850/900 /1800/1900MHz
|
|
WCDMA Band
|
850/2100 MHz
|
|
GPS sensitivity
|
-165dBm
|
|
GPS positioning accuracy
|
3-30m
|
|
Data transmission way
|
SMS,GPRS,HSDPA
|
|
Working temperature
|
-30°Cto+75°C
|
|
Storage temperature
|
-40°Cto+85°C
|
|
Working humidity
|
5-95%RH
|
|
Working voltage
|
DC 9V－36V
|
|
backup battery
|
3.7V / 450mAh
|
|
Standby current
|
< 50mA
|
|
Size
|
113*91*31 mm
|
|
Eight
|
0.695kg
|
7,Product accessories
1,External GPS antenna
2,External GSM antenna
3,Main interface cable
4,Vice wire Optional
4,Extension wire Optional (RS232, RS485)
6,User manual
7,SOS Button Optional
8,Hands-free speaker Optional
9,External microphone Optional
10,Two-Way call Handset Optional
11,External relay Optional
8, Trouble shooting
|
Fault phenomenon
|
Trouble shooting
|
|
Device can not be connected to the server after the first installation, shows offline on the platform
|
Please check if the main power cable connected correctly. Attention that do not connect it to car inner control lines.
|
|
SIM card installed well?
|
|
|
Check the parameter settings
|
|
|
Check if the terminal information already registered in the platform?
|
|
|
Is the ACC cable connected well? If yes, please turn it to ACC on.
|
|
|
Please check if the device got GPS fixed, if not, please test it in open sky environment for first GPS positioning.
|
|
|
Device shows offline on platform
|
Call the device SIM number, if it gets through?
|
|
Check SIM card credit, if the GPRS service is disable
|
|
|
If the car in the place without GSM coverage?
|
|
|
Check the offline time, it is offline occasionally or offline all the time, please check your GSM operator about the GPRS network.
|
|
|
Device can not get GPS location for long time/ Location deviation big from real location
|
Please check GPS antenna, place it face to sky.
|
|
Please check the place of GPS antenna, if there is material that can absorb electromagnetic waves (metal material), if there is Explosion-proof heat insulation membrane( with high metal composition that can absorb electromagnetic waves ) pasted on the window that upside the GPS antenna
|
|
|
If there is high building shield the GPS signal, please drive your car to open sky place for first time GPS locating, first locating will need 1-2minute.
|
|
|
LED light is off when power on
|
Please check the car battery if it is low
|
|
Please check if the main power cable connected correctly. Attention that do not connect it to car inner control lines.
|
|
|
Please check if the fuse of the main power connection cable is burnt or damaged.
|
Tel:+86-25-87771386 Fax:+86-25-87771386 Email:mr.sun@taffgps.com
《中华人民共和国增值电信业务经营许可证》ICP证编号：苏B2-20130193
All Rights Reserved 苏ICP备09057672号